Tensile Strength Of Round Bar A 6061 Friction Weld Joint Influenced By Changes Room Temperature

Muhammad Ikram Kido, Sugiarto Sugiarto, Djarot B Darmadi

Abstract


Aluminum alloy is non-Ferro material that very difficult to amalgamate using fusion welding, so it requires friction method. Friction welding is process for connecting metals without melting (solid state process), Process merging between the rotating speeds of material forces cause heat friction and at somepoint can be able to melt the materials and melting process occurs. The study aim is to determine tensile strength results from friction weld joints due to changes in ambient temperature of room. Material test is Aluminum A6061. Friction welding uses a lathe with rotation speed of 1600 rpm. The length size of material is 80 mm and 120 mm, diameter 15 mm, Champer angle 15°, 65 bar friction force for 60 seconds, final compressive force 375 bar for 60 seconds and variations in ambient temperature namely room temperature (T0),125 °C,150°C. The A 6061 joint produces the highest tensile strength at temperature 150 oC (188 MPa).


Keywords


Friction Welding, Tensile Strength, and Aluminum A6061

References


Bauccio, M. (Ed.). (1993). ASM metals reference book. ASM international.

Irawan, Y. S., Suprapto, W., & Oerbandono, T. (2017). Torsion Strength of Round Bar A6061 Friction Weld Joint Influenced by Friction Time, Upset Force and One-Side Cone Geometry. Journal of Environmental Engineering and Sustainable Technology, 4(2), 78-84.

Taban, E., Gould, J. E., & Lippold, J. C. (2010). Dissimilar friction welding of 6061-T6 aluminum and AISI 1018 steel: Properties and microstructural characterization. Materials & Design (1980-2015), 31(5), 2305-2311.

Pah, J. C. A., Irawan, Y. S., & Suprapto, W. (2018). Pengaruh Waktu dan Tekanan Gesek terhadap Kekuatan Tarik Sambungan Paduan Aluminium dan Baja Karbon pada Pengelasan Gesek Continuous Drive. Rekayasa Mesin, 9(1), 51-59.

Biradar, N. S., & Raman, R. (2012). Investigation of hot cracking behavior in transverse mechanically arc oscillated autogenous AA2014 T6 TIG welds. Metallurgical and Materials Transactions A, 43(9), 3179-3191.

James, J. A., & Sudhish, R. (2016). Study on Effect of Interlayer in Friction Welding for Dissimilar Steels: SS 304 and AISI 1040. Procedia Technology, 25, 1191-1198.

Shubhavardhan, R. N., & Surendran, S. (2012). Friction welding to join dissimilar metals. International journal of emerging technology and advanced engineering, 2(7), 200-210.

Irawan, Y. S., Imawan, B., Soenoko, R., & Purnomo, H. (2016). Effect of surface roughness and chamfer angle on tensile strength of round aluminum A6061 produced by continuous drive friction welding. Journal of Engineering and Applied Sciences, 11(6), 1178-1185.

Abdulla, F. A. M., Irawan, Y. S., & Darmadi, D. B. (2018). Tensile Strength and Macro-microstructures of A6061 CDFW Weld Joint Influenced by Pressure and Holding Time in the Upset Stage. Rekayasa Mesin, 9(2), 149-154.

Ambroziak, A., Korzeniowski, M., Kustroń, P., Winnicki, M., Sokołowski, P., & Harapińska, E. (2014). Friction welding of aluminium and aluminium alloys with steel. Advances in Materials Science and Engineering, 2014.

Tiwan, Aan Ardian. (2005). Penyambungan Baja Aisi 1040 Batang Silinder Pejal Dengan Friction Welding. Fakultas Teknik Universitas Negeri Yogyakarta

Tarmizi, T., & Prayoga, B. (2016). Analisa Sifat Mekanik dan Struktur Mikro pada Proses Friction Stir Welding Alumunium 5052. Jurnal Riset Teknologi Industri, 10(2), 105-118.

Callister, William D. (2013). Fundamentals Of Material Science and Engineering, 4th edition An Introduction. New York: John Wiley and Sons, Inc.

Himawan, Citrakara Upendra S.B.K. (2016). Tensile Strength and Type of Fracture Differences On the Result Low carbon steel (ST 37) GMAW Welds due Normalizing process. Essay, Department of Mechanical Engineering, Faculty of Engineering, State University of Malang.




DOI: http://dx.doi.org/10.28989/senatik.v5i0.346

Article Metrics

Abstract view : 435 times
PDF (Bahasa Indonesia) - 298 times

Refbacks

  • There are currently no refbacks.




Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Conference SENATIK P-ISSN :2337-3881 and  E-ISSN : 2528-1666

Jumlah penggunjung = Web Analytics orang

Statistik Senatik

Flag Counter